Description

The ABB PFSK130(Order Code:3BSE002616R1)is a PROFIBUS DP communication module designed for the ABB AC 800M programmable logic controller(PLC)platform within the System 800xA distributed control and safety system.It enables the AC 800M controller to act as a PROFIBUS DP Master or Slave,connecting to a wide range of field devices—including remote I/O stations(e.g.,ABB CI801),variable frequency drives(VFDs),motor protection relays,valve positioners,and third-party PROFIBUS-enabled equipment.

With dual isolated PROFIBUS ports,built-in galvanic isolation,and seamless integration into ABB’s engineering environment,the PFSK130 delivers robust,deterministic communication for process automation in demanding industries such as power generation,oil&gas,water treatment,and mining.

Application Scenarios

At a European cement plant undergoing digital modernization,legacy analog I/O for kiln temperature and fan speed control caused signal drift and maintenance delays.Engineers replaced local marshalling panels with ABB AC 800M controllers equipped with PFSK130 modules.These connected to remote ABB CI801 PROFIBUS I/O stations located near the kiln—reducing analog wiring by 90%.The PFSK130 operated as a PROFIBUS DP Master at 1.5 Mbps,polling 128 I/O points every 10 ms with zero communication faults over 18 months.During a lightning storm,the 500 V galvanic isolation prevented ground loops from damaging the controller—avoiding an estimated€220K in downtime.

Parameter

Main Parameters Value/Description

Product Model PFSK130

ABB Order Code 3BSE002616R1

Manufacturer ABB

Product Category PROFIBUS DP Communication Module–AC 800M I/O System

Compatible Controllers AC 800M PM86x series(e.g.,PM864,PM865,including redundant pairs)

Communication Standard PROFIBUS DP(EN 50170)–supports Master and Slave mode

Ports 2 x isolated PROFIBUS DP ports(9-pin D-SUB or optional RJ45 via adapter)

Baud Rate 9.6 kbps to 12 Mbps(auto-negotiable or fixed)

Max Devices per Port Up to 126 slaves(system-dependent)

Isolation Galvanic isolation(500 V RMS)between backplane and field bus

LED Indicators RUN,ERROR,SF(System Fault),BF(Bus Fault),TX/RX per port

Hot-Swap Support Yes–supported in redundant AC 800M configurations

Power Supply Powered via AC 800M backplane(no external supply needed)

Mounting Plugs into standard AC 800M I/O baseplate(e.g.,TB510,TB520)

Operating Temperature 0°C to+55°C

Certifications CE,UL,CSA,IEC 61000-6-2/4(EMC),SIL 2(per IEC 61508 when used in certified safety systems)

Configuration Tool Control Builder M(ABB’s engineering software)

Technical Principles and Innovative Values

Innovation Point 1:Dual Independent PROFIBUS Ports for Segmented Networks

Each port operates independently—allowing one to serve drives and the other remote I/O,improving reliability and simplifying network segmentation.

Innovation Point 2:Native PROFIBUS Stack Integrated in Control Builder M

No external GSD file management or third-party drivers:device configuration,diagnostics,and I/O mapping are handled directly in Control Builder M,reducing engineering time by up to 40%.

Innovation Point 3:Real-Time Diagnostics in System 800xA

PROFIBUS slave status,bus errors,and device alarms appear in System 800xA asset views—enabling predictive maintenance and rapid troubleshooting.

Innovation Point 4:Seamless Redundancy Support

In redundant AC 800M systems,the PFSK130 supports media redundancy protocols(e.g.,PROFIBUS Ring)or dual-master switchover—ensuring continuous operation during controller failover.

Application Cases and Industry Value

In a Middle Eastern desalination plant,the PFSK130 connects to 24 ABB ACS880 drives controlling high-pressure RO pumps.The module’s 12 Mbps capability ensures synchronized ramp-up during startup,preventing hydraulic shock.Over three years,zero communication-related trips occurred—despite ambient temperatures exceeding 50°C.

Similarly,at a U.S.biopharma facility,the PFSK130 interfaces with Siemens ET 200M I/O and Yokogawa valve positioners in a validated cleanroom process.Its audit trail and diagnostic logs satisfied FDA 21 CFR Part 11 requirements during regulatory inspection.

Related Product Combination Solutions

ABB AC 800M CPUs:PM864A,PM865(with redundancy kit for high availability)

Baseplates:TB510(standard),TB520(enhanced diagnostics)

Remote I/O:ABB CI801(PROFIBUS DP I/O station)

Drives:ABB ACS880,ACS580(with PROFIBUS adapter)

Engineering Software:Control Builder M,System 800xA

Alternative Modules:

MB510:For Modbus RTU/ASCII

CI854A:Older PROFIBUS module(PFSK130 is newer,higher performance)

CI860:For Foundation Fieldbus

GSD Files:Supplied by ABB for third-party device integration

PROFIBUS Analyzers:Siemens BT200 or Softing for advanced bus diagnostics

Installation,Maintenance,and Full-Cycle Support

Installation:

Insert PFSK130 into TB510/TB520 baseplate in AC 800M rack

Connect PROFIBUS cables with proper termination resistors(at both ends)and shield grounding

Configure in Control Builder M:assign station address,baud rate,and I/O mapping

Maintenance:

Monitor LED indicators for bus health

Use System 800xA to view slave diagnostics(e.g.,“Device Not Responding”)

Replace via hot-swap in redundant systems without shutdown

Lifecycle Support:

ABB continues to manufacture and support the PFSK130(3BSE002616R1)under its Long-Term Availability Program,with spare parts and technical documentation guaranteed until at least 2030.Firmware updates and compatibility patches are regularly released for new device integrations.

Contact us for a customized solution—whether you’re integrating PROFIBUS devices into a new AC 800M system,upgrading legacy automation,or ensuring reliable,high-speed field communication in critical infrastructure,the ABB PFSK130 delivers industrial-grade performance,cybersecurity-ready architecture,and seamless lifecycle support within the trusted ABB ecosystem.

选择深圳长欣，选择放心，售后无忧 大量现货，当天顺丰发货！！！