ABB BCU06-ETH C3 (1SAP140100R1170) – AC500 Compact PLC CPU with 256 KB Memory, Ethernet & Dual Serial Ports缩略图

ABB BCU06-ETH C3 (1SAP140100R1170) – AC500 Compact PLC CPU with 256 KB Memory, Ethernet & Dual Serial Ports

ABB BCU06-ETH C3 (1SAP140100R1170) – AC500 Compact PLC CPU with 256 KB Memory, Ethernet & Dual Serial Ports插图

 

Description

The ABB BCU06-ETH C3​ (ordering code 1SAP140100R1170) is a compact central processing unit (CPU) in ABB’s AC500 programmable logic controller family—and also the Ethernet-equipped evolution of the Advant Controller 31 (AC31) basic unit. It combines a 32-bit processor, 256 KB of user program memory, one 10/100 Mbps Ethernet port, two software-configurable serial ports, a FieldBusPlug (FBP) interface, an integrated LCD display with keypad, and an SD card slot—all in a single DIN-rail-mounted housing roughly the width of a paperback book.The BCU06-ETH C3​ is the “Goldilocks” controller of the ABB range: too capable for a micro-PLC slot, yet far more economical than a full-rack AC500 PM59x. Its defining characteristic is communication breadth delivered without option cards—Modbus TCP on Ethernet, Modbus RTU/ASCII on the serial ports, and a fieldbus of choice through the FBP connector—making it especially valuable in brownfield retrofits where legacy devices, modern SCADA, and mixed protocols must coexist in one cabinet.

Application Scenarios

A small municipal wastewater treatment plant relied on a BCU06-ETH C3​ to monitor tank levels, pH, and flow across more than a dozen analog inputs while controlling aeration blowers and influent pumps. The plant’s SCADA system communicated over Modbus TCP through the CPU’s Ethernet port, while one serial channel drove a variable-frequency drive and the other connected to a local HMI. When the plant’s maintenance technician needed to verify a blower interlock during a weekend shift, the CPU’s onboard LCD displayed the relevant I/O status directly at the cabinet—no laptop, no software license, no waiting for the controls engineer to arrive. That local diagnostic capability kept the plant running through minor fault events that would otherwise have triggered an after-hours service call.This is the practical niche the BCU06-ETH C3​ was built for: a controller that an operator can read at the panel and a technician can replace from a spare, without an engineering workstation or a download session.

Parameter

Main Parameters Value/Description
Product Model BCU06-ETH C3 (variant C3 = performance class, not a revision letter)
Ordering / Article Code 1SAP140100R1170
Manufacturer ABB (Automation Products / AC500 & Advant Controller 31 platforms)
Product Category Compact programmable logic controller CPU module
Processor 32-bit RISC-class processor
User Program Memory 256 KB (sufficient for thousands of rungs / lines of logic)
Data Memory 416 KB data area (sources vary; confirm against the ABB manual)
Ethernet Interface 1 × RJ45, 10/100 Mbps, auto-MDIX; Modbus TCP, UDP, HTTP, FTP
Serial Ports 2 × RS232 / RS485 software-switchable (COM1: programming/ASCII/MMC; COM2: Modbus master/slave/ASCII/MMC)
Fieldbus Interface FieldBusPlug (FBP) connector — accepts optional PROFIBUS-DP, DeviceNet, AS-Interface, Modbus modules
System Bus CS31 system bus for distributed remote I/O and slave units
Local Display Integrated LCD with RUN / DIAG / CFG / VAL keys for local diagnostics
Storage Expansion SD card slot (ABB MC502 card) for program backup, data logging, firmware & OS updates
Real-Time Clock Battery-backed RTC for time-stamped events and data records
Programming Standard IEC 61131-3 (LD, FBD, IL, ST, SFC) via Control Builder AC500 (PS501) / Automation Builder
Supply Voltage 24 V DC nominal (20.4–28.8 V DC range, ±10%), reverse-polarity protected
Power Consumption Approx. 10 W
I/O Expansion Up to 10 × S500 I/O modules locally; further remote stations via CS31
Battery Backup TA521 lithium battery for data retention
Protection Rating IP20 (designed for cabinet installation)
Operating Temperature 0 to +60 °C (commonly specified +5 to +55 °C; verify against the exact manual revision)
Storage Temperature -40 to +70 °C
Mounting Method Standard DIN-rail mount
Dimensions (W×H×D) Approx. 119 × 186 × 135 mm (mounting depth and orientation affect the figure)
Weight Approx. 0.45–1.2 kg (varies by source and included accessories)
Lifecycle Status Obsolete / legacy — supplied primarily as tested surplus, refurbished, or new-surplus